Weighs only 70 grms (2.5oz)
Clamps securely onto the XCS 15mm bars x 1.85” pitch
Constant-friction pivot for easy monitor positioning
New screw-in end caps with optional colour coding
Universal Monitor Bracket for XCS 15mm Bars
(15mm x 1.85” pitch)
This bracket comes in kit form. To buy this kit
As all the parts are printed together in one go, they will all be in black, including the end caps but you can buy a separate set of colour coded end caps here………………….
To complete the bracket you will also need;
One 1/4 UNC half-height hexagonal nut (only a 4mm high half-nut will allow the end caps to fit properly)
In the UK, I have found Westfield Fasteners a good source for UNC nuts and bolts and the links above are to their site.
This bracket fits onto the XCS camera plate’s 15mm x 1.85” pitch bars. The strong clamp force holds it firmly in place. All the parts are in black although colour coded end caps can be printed separately.
Any lightweight monitor with a 1/4” UNC screw mounting point in its base should fit, as long as the distance between the centre of the screw and the back of the monitor is less than 13 mm (0.5”).
It is lightweight, rigid and has a ‘constant friction pivot’ so the monitor can be tilted without loosening the thumbwheels. You simply screw down the thumbwheels to select the required friction and you’re good to go.
KIT ASSEMBLY - INITIAL PREPARATION
1. Carefully separate the thumbwheels and caps from each other.
The thumbwheels and caps are printed in groups of 3.
Use a sharp knife and be sure to remove all of the supporting sprues.
2. Carefully separate the ‘backrest’ from the ‘paddle’.
Use a sharp knife and be sure to remove all of the supporting sprue material.
3. Sometimes slight 3D printing variation means that the fit of the bolts in the printed holes is a little too tight.
If this is the case and the fit is a little too stiff then just widen the hole slightly by pushing a 1/4" bolt back and forth through the
hole until it can slide easily or you can use a drill and 1/4” bit.
4. When you slide the bolts into the thumbwheels, ensure the bolt head is sat all the way down at the bottom.
Sometimes there can be a small build up of excess printing powder on the inside corners of the thumbwheel, so if that’s the
case, just scrape it away before you put the bolt in. This will ensure enough room for the cap to screw into place.
1. Slide the 1/4” UNC x 2” bolt through one of the smaller thumbwheels and then through the base and paddle to form the pivot.
2. Push the 1/4” UNC half-nut into the remaining small thumbwheel and screw it onto the end of the 2” bolt.
3. Slide the larger remaining thumbwheel with the dovetail base into the slot in the paddle until the holes align and then push through the 1/4” UNC x 5/8” bolt.
4. Screw on the end caps. The two end caps with the larger split column go at the head end of the 2” and 5/8” bolts and the other one at the nut end. Once you’re happy that the cap screws on smoothly, you can put a spot of cynoacrylate glue (superglue/Krazyglue) on the cap thread to ensure it doesn’t come loose.
5. Once your monitor is mounted onto the ‘paddle’ you can fit the optional ‘backrest’. The ‘backrest’ stops the monitor from rotating.
Once you are happy with the fit of your monitor screwed onto the ‘paddle’, fit the ‘backrest’ in position in the slots and use superglue/Krazyglue to fix it.
6. Now just screw down the thumbwheels against each other until you’ve got your preferred stiffness and you’re good to go!
KIT ASSEMBLY - PUTTING IT ALL TOGETHER (refer to the pictures below)
REMOVE BACKREST FROM PADDLE